1 ms type lower profile plug h/ms series new 2004.6 features 1. 20% height reduction when compared with existing h/ms series connectors the overall height of plug assemblies is lower, allowing it to be used in space constrained applications. 2. cable exit in 360 directions the cable can exit in any of the 8 fixed direction, in 45 increments. 3. simple assembly the 2-piece design consisting of the contact/insulator assembly and the back-shell assembly allows termination without the use of any specialized tools. 4. water and dust protection ip 67 rating when fully terminated and mated with corresponding part. 5. tuv certification provided with a protective circuit function for tuv certification. the (d) pin is directly connected to the outside metal case. applications factory automation equipment, robotic equipment, servo motors, and a wide variety of industrial and measuring instruments. plug (45) can be changed in 45 degree increments connector height comparison existing ms connector lower-profile plug 22-22 size cable exit direction of 360 circular connector conforming to mil-c-5015 pat. p 50.1mm 54.5mm 70mm 3057-10 18 45.5mm 41mm 56.5mm 3057-10 48.2mm 60.7mm 78.7mm 3057-12 22 53.2mm 63.8mm 45.8mm 3057-12 existing ms connector lower-profile plug 18-10 size
2 3 m ohms max. 1 m ohms max. 5000 m ohms min. no flashover or insulation breakdown. contact resistance: contact resistance: 4.5 m ohms max. 1.5 m ohms max. insulation resistance: 5000 m ohms min. insulation resistance: 50 m ohms min. (humidity state) 500 m ohms min. (dry state) when mated with corresponding connector. 1a dc 500 v dc 2250v ac/one minute. frequency: 10 to 500 hz, single amplitude of 0.75 mm, acceleration of 98 m/s 2 for 3 hours in 3 axis. acceleration of 490 m/s 2 , 11ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. 500 cycles temperature: -55? ? room temperature to +125? ? room temperature time: 30 ? 10 to 15 ? 30 ? 10 to 15 (minutes) 5 cycles. 96 hours at temperature of 71? and humidity of 95% . no dust penetration. no water penetration when submerged for 0.5 hour at the depth of 1 meter. 1. contact resistance 2. insulation resistance 3. withstanding voltage 4. vibration 5. shock 6. durability (insertion/ withdrawal) 7. temperature cycle 8. humidity 9. water/dust protection rating voltage rating 250vac, 250v dc (pollution degree: 3, overvoltage category: 3 ) 500v ac, 500v dc (pollution degree: 2, overvoltage category: 2 ) current rating 23a max. (18-10 size) 46a max. (22-22 size) operating temperature range -25? to +125? storage temperature range -25? to +125? product specifications materials item specification 18-10 size 22-22 size conditions body insulator socket contacts gasket bushing aluminum alloy pps copper alloy silicone rubber chloroprene rubber black chromate color: black silver plating color: black color: black ------------------- ul94v-0 ------------------- ------------------- ------------------- item material finish remarks additional product information 1. product number suffixes (10) supplied with a wire hole in the locking ring (to prevent loosening of the ring). (11) supplied without the wire hole in the locking ring. 2. corresponding receptacles. 18-10 size: part number h/ms3102a18-10p-d-t1(10) 22-22 size: part number h/ms3102a22-22p-d-t(10) no electrical discontinuity for 10 ms max.
3 plug a b c 18-10s x 3057-10 d 41 31 ?33.5 45.5 part number cl no. number of contacts h/ms08a18-10s-dt10d(10) h/ms08a18-10s-dt10d(11) h/ms08a18-10s-dt10d1(10) h/ms08a18-10s-dt10d1(11) 120-0476-3-10 4 weight 89g applicable cable diameter ?12~?14.3mm ?10~?12.5mm contact solder pot inner diameter 2.5mm 120-0476-3-11 120-0481-3-10 120-0481-3-10 part number cl no. number of contacts h/ms08a18-10s-dt10c(10) h/ms08a18-10s-dt10c(11) 120-0480-0-10 4 weight 77.6g applicable cable diameter ?13~?14.3mm contact solder pot inner diameter 2.5mm 120-0480-0-11 part number cl no. number of contacts h/ms08a22-22s-dt12d(10) h/ms08a22-22s-dt12d(11) h/ms08a22-22s-dt12d1(10) h/ms08a22-22s-dt12d1(11) 120-0477-6-10 4 weight 127g applicable cable diameter ?13~?15.9mm ?10~?13.5mm contact solder pot inner diameter 4.5mm 120-0477-6-11 120-0482-6-10 120-0482-6-11 shown one type. shown one type. shown one type. a b c 18-10s x d 41 35.5 ?30 ?33.5 x b c 22-22s d a 3057-12 45.8 53.2 36 ?39.5 h/ms08a18-10s-dt10d(10) h/ms08a18-10s-dt10c(10) h/ms08a22-22s-dt12d(10)
3057-10 a b bushing back-shell cable contacts strain relief clamp washer solder insulator/contact assembly pre-solder conductor portion b b a 4 b assembly procedures outline of assembly process 1 2 a. pass the strain relief clamp, washer, bushing, and hood over the cable, in this order. b. prepare the cable and conductors per the dimensions in table 1. c. bend the exposed conductor to the b dimension as indicated in table 1. d. pre-solder the exposed conductor and solder it as shown to the exposed contact. note: use care not to damage the conductors insulation. a. place over the contact/insulator assembly (in the following order:back shell, bushing, washer, strain relief clamp). b. tighten the locking ring and cable clamp to the torque values per table 2. c. tighten the set screw to a torque value of 0.3-0.4 n-m hrs recommended tool: pb205/1.27 (cl150-0066-3)or equivalent. d. using screwdriver tighten the two strain relief clamp screws until both sides of the moveable part are in contact with the c able clamp. a b 18-10 size table 1 22-22 size 24mm 13mm 33mm 15mm the contents of this catalog are current as of date of publication. contents are subject to change without notice for the purpo se of improvements. 5-23,osaki 5-chome,shinagawa-ku,tokyo 141-8587,japan phone: 81-3-3491-9741, fax: 81-3-3493-2933 http://www.hirose.com locking ring cable clamp table 2 3 to 3.5n ? m 5 to 6n ? m 3057-10 4.5 mm min. cable strain relief clamp back-shell locking ring screw clamp washer bushing set screw (hexagonal hole opposite side 1.27 mm)
|
